|
|
 |
|
 |
|
900 SERIES SINGLE REDUCTION
BASE TYPE GEAR DRIVES
NOTE: Bracketed numbers in table below refer to Notes section below table.
Average Shipping Weight: 65 Lbs.
|
MODEL
|
RATIO (2)
|
RATINGS (1)
|
GEARBOX (4) INERTIA (LB-FT 2)
|
DIA A. (INCHES)
|
|
OUTPUT (RPM)
|
INPUT HORSEPOWER
|
OUTPUT TORQUE (IN-LB)
|
INPUT SHAFT (3) OVERHUNG LOAD CAPACITY (LBS)
|
OUTPUT SHAFT (3) OVERHUNG LOAD CAPACITY (LBS)
|
|
9013 (5)
|
1.315
|
1331
|
79.2 (6)
|
3750
|
75
|
500
|
0.13
|
1 1/4
|
|
9015 (5)
|
1.551
|
1128
|
70.9 (6)
|
3960
|
75
|
500
|
0.11
|
1 1/4
|
|
9019 (5)
|
1.907
|
918
|
59.7 (6)
|
4100
|
75
|
500
|
0.10
|
1 1/4
|
|
9020 (5)
|
2.049
|
854
|
55.6
|
4100
|
75
|
500
|
0.09
|
1 1/4
|
|
9022 (5)
|
2.205
|
794
|
51.6
|
4100
|
75
|
500
|
0.08
|
1 1/4
|
|
9024 (5)
|
2.378
|
736
|
47.7
|
4090
|
75
|
500
|
0.08
|
1 1/4
|
|
9028 (5)
|
2.788
|
628
|
39.6
|
3980
|
150
|
1000
|
0.05
|
1 1/4
|
|
9030
|
3.032
|
577
|
36.0
|
3930
|
150
|
1000
|
0.04
|
1 1/4
|
|
9033
|
3.310
|
529
|
32.5
|
3870
|
150
|
1000
|
0.04
|
1 1/4
|
|
9036
|
3.630
|
482
|
29.3
|
3830
|
150
|
1000
|
0.04
|
1 1/4
|
|
9040
|
4.000
|
438
|
25.2
|
3630
|
200
|
1000
|
0.03
|
1 1/4
|
|
9042
|
4.208
|
416
|
23.6
|
3580
|
200
|
1000
|
0.03
|
1 1/4
|
|
9044
|
4.435
|
395
|
22.0
|
3510
|
200
|
1000
|
0.03
|
1 1/4
|
|
9047
|
4.682
|
374
|
20.2
|
3410
|
325
|
1000
|
0.03
|
1 1/4
|
|
9049
|
4.952
|
353
|
18.8
|
3360
|
325
|
1000
|
0.03
|
1 1/4
|
|
9052
|
5.250
|
333
|
17.6
|
3330
|
450
|
1000
|
0.02
|
1 1/8
|
|
9056
|
5.579
|
314
|
15.9
|
3200
|
450
|
1000
|
0.02
|
1 1/8
|
|
9059
|
5.944
|
294
|
14.5
|
3110
|
400
|
1000
|
0.02
|
1
|
|
9063
|
6.353
|
275
|
13.1
|
3000
|
400
|
1000
|
0.02
|
1
|
|
9068
|
6.813
|
257
|
12.0
|
2930
|
400
|
1000
|
0.02
|
1
|
NOTES
-
Horsepower, torque, output speed and overhung load capacities based on 1750 rpm input speed and 1.00 Service Factor.
-
Non-standard ratios available. Consult Dorris Company if desired ratio is not shown.
-
Overhung load is measured at the midpoint of the key for the input and output shafts respectively.
-
Measured at the input shaft.
-
If a backstop is required consult Dorris Company for backstop torque capacity as it is less than the output torque rating shown.
-
Consult Dorris Company for thermal capacity in your application.
|
|
 |
|
 |
| © 2008 SGC Industries, Inc. All Rights Reserved. |
This website designed and maintained by IGD Solutions Corporation |
|
|
Base Type Drive
TL Series Screw Conveyor
View Shopping Cart